Signs are everywhere in daily life. Excellent signs can enhance the overall image of the place. So, what should we pay attention to if we want to make a good sign?
01 铝合金型材要求
01 requirements for aluminum alloy profiles
1、铝合金型材和常用塑胶材料配件应符合铝合金标牌型材的质量要求。
1. Aluminum alloy profile and common plastic material accessories shall meet the quality requirements of aluminum alloy nameplate profile.
2、铝合金型材的角底偏差少于正负偏差1度。
2. The angle bottom deviation of aluminum alloy profile is less than 1 degree of positive and negative deviation.
3、平面间隙<=0.4%*B(B为型材宽度)。
3. Plane clearance < = 0.4% * B (B is the profile width).
02 亚克力标牌加工要求
02 acrylic label processing requirements
1、亚克力出模热弯成形，尺寸及形状一致，表面无气泡及划痕。
1. Acrylic die hot bending, the size and shape of the same, no bubbles and scratches on the surface.
2、热弯成形后表面经过粗砂、细砂、碾磨处理，保证其表面平滑无台阶。
2. After hot bending, the surface is treated by coarse sand, fine sand and grinding to ensure that the surface is smooth without steps.
3、完成后表面光泽柔和均匀、无颗粒状物、无气泡、透光均匀。
3. After completion, the surface luster is soft and uniform, without particles, bubbles and even light transmission.
03 不锈钢工艺要求
03 stainless steel process requirements
1、不锈钢板须刨坑折弯焊接（不锈钢板须先刨坑后折弯，以保证边缘挺拔度）；保证折弯处圆弧角R＜1MM。
1. The stainless steel plate shall be planed, bent and welded (the stainless steel plate shall be planed first and then bent to ensure the edge straightness); the arc angle R at the bending position shall be less than 1mm.
2、焊接前表面油污，减少焊缝形成的虚焊、气孔、裂纹等缺陷。
2. Before welding, the oil stain on the surface shall be removed to reduce the defects such as false welding, air hole, crack and so on.
3、焊接完后将所有可见焊缝打磨光滑，与周围表面一样平滑，无明显划痕。
3. After welding, all visible welds shall be polished smooth, as smooth as the surrounding surface, without obvious scratches.
04 烤漆工艺
04 paint baking process
1、清洗表面残留物、补灰、打磨等一系列表面处理。
1. A series of surface treatment, such as cleaning surface residue, mending ash, grinding, etc.
2、采用型油漆烤漆处理。烤漆房须无尘埃颗粒车间，烤漆表面涂层三涂三烤处理，涂层厚度大于或等于35微米。
2. Environmental friendly high quality paint baking treatment is adopted. The paint room shall be free of dust particles, and the surface coating of the paint shall be painted three times and baked three times, and the coating thickness shall be greater than or equal to 35 microns.
3、油漆色彩要符合设计方案要求。
3. Paint color shall meet the requirements of design scheme.
4、面漆膜应平滑、均匀，不允许出现流痕、皱纹、桔皮、气泡、夹杂等影响装饰效果的缺陷。
4. The finish film shall be smooth and uniform, and no defects such as flow marks, wrinkles, orange peel, bubbles, inclusions, etc. that affect the decoration effect are allowed.
05 丝印工艺要求
05 silk screen printing process requirements
1、菲林冲制网版，丝印表面用酒精或白电油将表面清理干净。
1. Feilin is used to make screen plates, and the surface of screen printing is cleaned with alcohol or white electric oil.
2、丝印色彩要符合设计方案要求，字体及图案笔划清晰，无变形、锯齿等缺陷。
2. The color of screen printing shall meet the requirements of the design scheme, the font and pattern strokes shall be clear, and there shall be no deformation, sawtooth and other defects.
3、丝印图形文字颜色与底色对比无明显渗透现象。
3. There is no obvious penetration between the color of silk screen graphics and the background color.
06 安装要求
06 installation requirements
1、安装完成后标识牌外观精美、表面无螺钉、无划痕、气泡及明显的颜色不均匀，烤漆须无明显色差，所用材料符合设计方案要求。
1. After installation, the signboard shall have a beautiful appearance, no screws, scratches, bubbles and obvious uneven color on the surface, no obvious color difference on the baking paint, and the materials used shall meet the requirements of the design scheme.
2、标牌安装方式应方便面板更换及维护。
2. The installation of signs shall be convenient for panel replacement and maintenance.
