In the whole process of video post production, there are several aspects to pay special attention to, such as: interface output, cutting, patching, mounting, covering sub film and so on. All the mistakes in the design and production of inkjet advertising lead to the success and failure of inkjet advertising. Next, we will give you a detailed introduction to the problems that we must pay attention to in the process of production in the later stage.
1、喷绘广告宣传輸出：针对图象的輸出，精密度关重要，欧帆对全部广告宣传的精密度制做，全是1440DPI，确保了界面的真实复原。颜色輸出规定为CMYK，颜色复原度提高。
1. Print advertising output: for image output, precision is very important. Oufan's precision of all advertising is 1440dpi, which ensures the real restoration of the interface. The color output is specified as CMYK, and the color recovery is improved.
2、喷绘广告宣传裁剪：针对界面尺寸与打印纸张相距很大需裁剪的，需要量剪齐整。在大家裁膜时，也运用剪子顺着道路标线走齐，由于会便捷在覆亚膜中的上膜工作中，且更能保质保量与通过率。
2. Inkjet advertising cutting: for the interface size and printing paper is far from the need to cut, the amount of cutting neat. When you cut the film, you also use the scissors to go along the road marking, because it will be convenient to apply the film in the covering sub film, and it can guarantee the quality and quantity and pass rate.
3、喷绘广告宣传拼凑：广告宣传界面的拼凑部位要搞清楚，界面左右部位明确好。在輸出全过程中，由于要輸出的界面是同一张图，因而尽量维持其颜色一致和尺寸相对，要纪录輸出时的设定参改，保证准确无误。
3. Inkjet advertising patchwork: the patchwork of advertising interface should be clear, and the left and right parts of the interface should be clear. In the whole process of output, since the interface to be output is the same picture, the color and size of the interface should be consistent as far as possible, and the setting parameters should be recorded to ensure accuracy.
4、喷绘广告宣传裱板：为了更好地使界面的四边完好无损的宣传栏边沿符合，大家先将界面沿在其中的相邻两侧裁齐，然后此后两侧为标准，两端对齐宣传栏的边沿。用裁纸刀沿宣传栏的卡条，将界面不必要的一部分裁去，即把整副画裱完。
4. Spray painting advertising mounting board: in order to make the edges of the billboard with intact four sides of the interface conform to each other, we first cut the interface edge on the adjacent two sides, and then the two sides are the standard, and the two ends are aligned with the edge of the billboard. Use a paper cutter to cut the unnecessary part of the interface along the card bar of the bulletin board, that is, to mount the whole picture.
5、喷绘广告宣传界面覆亚膜：喷绘广告宣传为了更好地维持实际效果，会在广告宣传外开展覆亚膜。覆亚膜时是调整滚子轴承的旋扭，拿到觉得沒有摩擦阻力才行、微紧。广告宣传界面覆亚膜将膜平整送进，确保在膜行走的全过程中不造成侧偏，膜沒有受挤压成型状。随后，将膜拉上，在膜将要停止时，将滚子轴承控住，用劲拉一下膜，确保顶端齐平。
5. Sub film covering of ink-jet advertising interface: in order to better maintain the actual effect, sub film covering will be carried out outside the advertising. When covering sub film, it is the first to adjust the rotation and torsion of the roller bearing, so that it can be slightly tight without friction resistance. The advertising interface is covered with sub film to send the film smoothly to ensure that the film does not deviate during the whole process of walking, and the film is not extruded. Then, pull the film up. When the film is about to stop, hold the roller bearing and pull the film hard to ensure that the top is flush.
以上是关于在制作喷绘广告后期时需注意的问题，希望对大家有所帮助，如想要了解更多内容欢迎点击济南喷绘广告公司https://www.hongchenad.com官网。
The above is about the production of ink-jet advertising needs to pay attention to the problem, hope to help you, if you want to know more, welcome to Jinan spray painting advertising company https://www.hongchenad.com Official website.
