In addition to high-quality design and exquisite production process, it is also very important to choose a suitable installation method for an advertisement signboard. The installation mode must be selected according to the characteristics of the billboard and the installation environment. Next, Jinan sign production company will check 8 common installation methods in advertising signs for you!
1粘贴式
1 paste
粘贴式应用范围广泛，常用的粘合胶有玻璃胶、泡沫胶、结构胶等。要根据广告标识材质及安装环境、内外干湿、温差等各种情况综合考虑，选择合适的胶粘剂。发光字运用很多的粘贴方式是玻璃胶安装，像树脂字、无边字、注塑字都可选择玻璃胶粘贴式安装。
The adhesive type is widely used. The commonly used adhesives are glass glue, foam glue, structural adhesive, etc. It is necessary to select the appropriate adhesive according to the advertising sign material and installation environment, internal and external humidity, temperature difference and other conditions. There are many ways to paste the light-emitting words, such as resin words, borderless words and injection words.
2粘贴吊挂式
2 paste hanging type
适用于一些折边标识。如果安装墙体基础是大理石、玻璃、不锈钢这类不允许打孔，而且又坚固平整的安装墙，那这种方法是很适合不过的了。准确测量好安装位置，以防把标识装歪，用AB胶将有机边条或角铝等材料粘在墙体上，然后将标识折边挂上，微调位置，用玻璃胶固定即可。
It is suitable for some hem marks. If the installation wall is based on marble, glass, stainless steel, which is not allowed to drill, but also solid and flat installation wall, this method is very suitable. Firstly, the installation position shall be measured accurately to prevent the sign from being installed askew.
3吊挂固定式
3 hanging fixed type
这是针对一些折边标识，体积较大、质量重、用泡沫填充粘贴无法安装所采用的方式。确定打孔点，用冲击钻打孔，钉上胶塞及自攻螺丝。只用一只螺丝时，必须在标识标牌的上沿中间部位打孔，以保持水平，然后将标识折边挂在螺丝上，调整位置后，四周封上玻璃胶固定即可。
This is for the use of some flanging labels, large volume, heavy weight, with foam filling and paste can not be installed. First, determine the drilling point, use the impact drill to drill holes, screw on the rubber plug and self tapping screw. When only one screw is used, holes must be drilled along the middle part of the upper edge of the sign plate to keep it horizontal. Then, hang the sign hem on the screw. After adjusting the position, seal the glass glue around to fix it.
4底板内部打螺丝式
4 screw type inside the bottom plate
这种安装方法针对于金属底盒的标识，如吸塑字、平面发光字这类标识。安装时先根据测量的尺寸在安装墙及标识金属底板上钻好孔，将底盒用螺丝固定于安装墙上，再将字壳用螺丝安装于底盒上面。
This installation method is for the identification of metal bottom box, such as blister type, flat light-emitting type. During installation, first drill holes on the installation wall and mark metal base plate according to the measured size, fix the bottom box on the installation wall with screws, and then install the word case on the bottom box with screws.
5悬挂式
5 hanging type
这种方式所采用的吊链材料主要有铁链、钢索、吊鱼丝、扎带等。可根据室内外环境、标识标牌制作重量及其它一些特殊要求采用合适吊装材料。吊牌灯箱通常就是运用这种安装方法。
The chain materials used in this way mainly include iron chain, steel cable, fish hanging wire, tie belt, etc. Suitable hoisting materials can be used according to indoor and outdoor environment, production weight of signs and other special requirements. This installation method is usually used for the pendant light box.
6落地式
6 floor standing
根据设计要求，将标识放置于相应位置即可。金属双面字大部分以落地式的方式安装。
According to the design requirements, the logo can be placed in the corresponding position. Most of the double-sided metal characters are installed in a floor type way.
7填埋式
7 landfill type
适用于地面为土壤结构，标识不需要移动的情况。根据标识的大小、高低来确定要挖的坑的大小以及所需要用到的混凝土的多少。宣传栏、导视牌大部分都运用这种方式安装。
It is applicable to the situation that the ground is soil structure and the mark does not need to be moved. According to the size and height of the sign, determine the size of the pit to be dug and the amount of concrete to be used. Most of the billboards and guide boards are installed in this way.
8螺杆安装式
8 screw mounted
螺杆安装是在标识的底板上焊接有一定长度的螺杆，安装墙面有相应的安装孔，安装时标识的螺杆直接插入对应的安装孔固定即可。螺杆安装是为了使标识离安装墙面之间具有一定的间距。在发光字中，背打光字基本都是运用螺杆安装，这是考虑到它本身的发光特性。
Screw installation is to weld a certain length of screw on the marked bottom plate, and install the wall with corresponding installation holes. During installation, the marked screw is directly inserted into the corresponding installation holes for fixation. Screw installation is to make the mark have a certain distance from the installation wall. In the light-emitting words, the back type light words are basically installed by screw, which is to consider its own light-emitting characteristics.
其实，广告设计制作中标识标牌制作的安装方法是非常灵活的，要根据实际安装情况而定。对于一些安装环境与自身机构都比较复杂的标识，往往需要多种安装方法结合使用才能完成安装。济南标识标牌制作公司的分享就到此结束，更多干货内容，敬请济南标识标牌制作公司官网https://www.hongchenad.com！
In fact, the installation method of logo and sign making in advertising design and production is very flexible, which should be determined according to the actual installation situation. For some signs with complex installation environment and its own mechanism, it often needs a variety of installation methods to complete the installation. This is the end of the sharing of Jinan logo production company. For more dry goods, please visit the official website of Jinan logo production company https://www.hongchenad.com !
